2024 SchemeBETASemester S1• Computer Science and Engineering
Introduction to Electrical and Electronics Engineering
2024 Scheme Syllabus & PYQ Analysis • GXEST104
Module:
Priority:
Module 1DC Circuits, Network Analysis & Magnetic Circuits
15 MarksOhm's Law, Kirchhoff's Laws (KCL, KVL) & Nodal Analysis
High Priority10x in Past Papers
EXAM NOTE
KCL based on charge conservation (Σ = Σ ). KVL based on energy conservation (Σ V = 0 around closed loop). In Nodal Analysis, choose reference node, write ( - )/R branch current equations, and solve node voltages.
Mesh (Loop) Analysis & Star-Delta (T-Π) Transformations
High Priority10x in Past Papers
EXAM NOTE
Set up matrix form . Star to Delta formulas: . Delta to Star: . Solve bridge networks using Star-Delta conversion.
Magnetic Circuit Fundamentals: MMF, Flux, Reluctance & B-H Curve
High Priority9x in Past Papers
EXAM NOTE
Magnetic Ohm's Law: Flux , where and Reluctance . Tabulate comparison between electric and magnetic circuits (EMF vs MMF, Current vs Flux, Resistance vs Reluctance, Conductivity vs Permeability).
Faraday's Laws, Statically vs Dynamically Induced EMF & Inductor Energy Storage
High Priority9x in Past Papers
EXAM NOTE
Faraday's First and Second Laws: (Lenz's law negative sign). Statically induced EMF: Mutually and Self induced (transformer action). Dynamically induced EMF: Conductor moves across magnetic field (, generator action). Energy stored in magnetic field: .
Module 2AC Fundamentals & Three-Phase Systems
15 MarksAC Waveform Parameters: Peak, Average, RMS Values & Form Factor
High Priority10x in Past Papers
EXAM NOTE
Derive for sinusoidal wave: ; . Form Factor . Peak Factor . Define phase angle, frequency, and period.
R-L, R-C & R-L-C Series AC Circuits: Impedance & Phasor Diagrams
High Priority10x in Past Papers
EXAM NOTE
Impedance where and . Magnitude . Phase angle . Resonance condition: . Draw voltage and impedance triangles.
Three-Phase AC Systems: Star vs Delta Connections & Power Measurement
High Priority10x in Past Papers
EXAM NOTE
Star (Y): = sqrt(3) , = . Delta (Δ): = , = sqrt(3) . Total three-phase power P = sqrt(3) cos θ = 3 cos θ in both star and delta. Two-wattmeter method: P = W1 + W2; tan θ = sqrt(3) * (W1 - W2) / (W1 + W2).
Active, Reactive & Apparent Power, and Power Factor Improvement
High Priority9x in Past Papers
EXAM NOTE
Power triangle: Active power P = V I cos θ (Watts), Reactive power Q = V I sin θ (VAR), Apparent power S = V I (VA). Power factor cos θ = P / S = R / |Z|. Disadvantages of low power factor (higher line current, larger conductor size, high transmission losses). Shunt capacitor power factor correction.
Module 3Electronic Devices, Regulated Power Supplies & BJT Amplifiers
15 MarksPN Junction Diode: V-I Characteristics & Half-Wave / Full-Wave Rectifiers
High Priority10x in Past Papers
EXAM NOTE
Forward bias (depletion layer narrows, cut-in voltage ~0.7V for Si, ~0.3V for Ge). Reverse bias (depletion layer widens, reverse saturation current ). Rectifier comparison: Half-wave (η = 40.6%, Ripple factor γ = 1.21, PIV = ), Full-wave Center-tapped (η = 81.2%, γ = 0.482, PIV = 2V_m), Full-wave Bridge (η = 81.2%, γ = 0.482, .
Zener Diode Working, Breakdown Mechanisms & Voltage Regulation
High Priority10x in Past Papers
EXAM NOTE
Heavily doped PN junction operating in reverse breakdown. Zener breakdown (quantum tunneling, narrow depletion layer, < 6V, negative temp coefficient) vs Avalanche breakdown (impact ionization, wide depletion layer, > 6V, positive temp coefficient). In voltage regulator circuit, explain regulation for variable input voltage and variable load resistance .
Bipolar Junction Transistor (BJT): Configurations & Common Emitter (CE) Characteristics
High Priority10x in Past Papers
EXAM NOTE
Three regions: Active (EB forward, CB reverse), Cut-off (both reverse), Saturation (both forward). Common Emitter (CE) configuration input characteristics ( vs at constant ) and output characteristics ( vs at constant ). Current gains: α = / , β = / , relation β = α / (1 - α).
Single-Stage RC Coupled BJT CE Amplifier: Circuit Operation & Frequency Response
High Priority9x in Past Papers
EXAM NOTE
Circuit diagram: Voltage divider biasing (R1, R2), collector load , emitter resistor , bypass capacitor , coupling capacitors and . Explain 180° phase inversion between input and output. Plot frequency response curve and explain gain roll-off at low frequencies (coupling/bypass capacitors) and high frequencies (parasitic junction capacitances).
Module 4Communication Systems & Electronic Instrumentation
15 MarksCommunication System Block Diagram & Modulation Schemes (AM vs FM)
High Priority10x in Past Papers
EXAM NOTE
Communication elements: Information source, Transmitter, Channel (with noise), Receiver, Destination. Need for modulation: Antenna height reduction (λ = c/f), multiplexing, noise immunity. Compare Amplitude Modulation (AM: envelope contains message, susceptible to noise) and Frequency Modulation (FM: constant amplitude, high noise immunity, larger bandwidth).
Optical Fiber Communication: Principle, Numerical Aperture & Advantages
High Priority9x in Past Papers
EXAM NOTE
Working principle: Total Internal Reflection (TIR) at Core-Cladding interface ( > , angle of incidence θ > θ_c = arcsin(n2/n1)). Numerical Aperture NA = sqrt(n1² - n2²). Acceptance angle θ_a = arcsin(NA). Mention key advantages: immense bandwidth, immune to EMI, low signal attenuation.
Electronic Instrumentation: Digital Multimeter (DMM) & Cathode Ray Oscilloscope (CRO)
High Priority9x in Past Papers
EXAM NOTE
DMM block diagram: Input attenuator, AC-to-DC converter, current-to-voltage converter, resistance constant current source, Dual-Slope ADC, and 7-segment digital display. CRO/DSO block diagram: CRT (Electron gun, deflection plates, phosphor screen), vertical amplifier, time base generator, trigger circuit. Measurement of voltage, frequency, and phase angle (Lissajous patterns).
Cellular Mobile Systems: GSM Architecture & Frequency Reuse
High Priority8x in Past Papers
EXAM NOTE
GSM architecture blocks: Mobile Station (MS with SIM), Base Station Subsystem (BSS: BTS + BSC), Network and Switching Subsystem (NSS: MSC, HLR, VLR, AUC, EIR). Explain cellular concept, frequency reuse clusters, and handoff / handover mechanisms.
Spot an error, wrong question, or missing topic? Let us know so we can fix it right away!
