Back to Search
Past Papers ↗
2024 SchemeBETASemester S1• Computer Science and Engineering

Engineering Graphics and Computer Aided Drawing

2024 Scheme Syllabus & PYQ Analysis • GMEST103

Beta: Curated from KTU syllabus & university papers. Spot an error or missing topic? Let us know!
12High Priority
4Modules
16+Papers Analyzed
60MTotal Marks
Module:
Priority:

Module 1Projections of Straight Lines & Traces (Drawing Problems)

15 Marks
Exam Focus: 100% Geometric Drawing on drawing sheets. Projections of lines inclined to both HP and VP, determination of true length, true inclinations (theta and phi), apparent angles (alpha and beta), and location of Horizontal Trace (HT) and Vertical Trace (VT). Zero theory questions.

Line Inclined to Both Planes: Given End Projector Distance & End Coordinates

High Priority10x in Past Papers
Rate:
Exam Sessions:
2024 Model Paper Q1June 2024Dec 2023Dec 2022
Question Type:15 Marks Drawing Problem
💡EXAM NOTE
Always use 2H pencil for construction lines and projection rays; darken final front and top views with H pencil. Use the Rotating Line method: (1) Mark reference line XY and plot projector of end C. (2) Plot projector of end D at given projector distance D = 70 mm. (3) Connect apparent views c'd' and cd. (4) Rotate cd parallel to XY to find true length and true inclination theta in front view; rotate c'd' parallel to XY to find true length and phi in top view. Locate HT on HP and VT on VP.

Line Inclined to Both Planes: Given True Length & True Inclinations (Theta & Phi)

High Priority9x in Past Papers
Rate:
Exam Sessions:
2024 Model Paper Q2June 2024May 2023
Question Type:15 Marks Drawing Problem
💡EXAM NOTE
When true length (TL) and true inclinations (theta to HP, phi to VP) are given: (1) Draw true lengths at true angles theta and phi from one end point. (2) Project ends to find loci of c' and c. (3) Project true length endpoints to locus lines to construct apparent front view c'd' and top view cd. (4) Extend apparent lines to XY to locate VT and HT. Verify: projectors of d' and d must lie along the exact same vertical line perpendicular to XY.

Line Contained in Profile Plane / Special Positions & Traces

Medium Priority8x in Past Papers
Rate:
Exam Sessions:
KTU June 2023KTU Dec 2022
Question Type:15 Marks Drawing Problem
💡EXAM NOTE
When a line lies in a profile plane (both end projectors coincide on the same perpendicular line to XY): (1) Front view and top view appear as a single vertical line. (2) Draw side view / profile view on X1Y1 reference plane to determine true length and true angles theta and phi. (3) Label HT and VT where the extended line strikes XY.

Line Intersection & Shortest Distance between Point and Reference Line

Medium Priority7x in Past Papers
Rate:
Exam Sessions:
KTU June 2023KTU Dec 2021
Question Type:15 Marks Drawing Problem
💡EXAM NOTE
To find true inclination and true length of a guy wire or tripod leg: Set up coordinate planes representing the ground (HP) and wall/pole (VP). Measure all coordinates from origin. Check that true length is obtained by rotating the apparent line about one apex point until parallel to XY.

Module 2Projections of Solids Inclined to Both Planes (Drawing Problems)

15 Marks
Exam Focus: 100% Geometric Drawing. Three-stage orthographic projections of solids (Pyramids, Prisms, Cones, Cylinders) resting on base corner, slant edge, generator, or face, with axis inclined to both reference planes. Zero theory questions.

Projections of Cone / Cylinder with Generator Resting on HP & Axis Inclined to VP

High Priority10x in Past Papers
Rate:
Exam Sessions:
2024 Model Paper Q3June 2024Dec 2023Dec 2022
Question Type:15 Marks Drawing Problem
💡EXAM NOTE
Three-stage projection: (1) Simple position: Base on HP, draw circle top view and triangular front view. Divide base circle into 12 equal parts. (2) Tilt front view so that one extreme generator o'g' lies flat on XY (on HP). Project top view down. The base circle projects as an ellipse. (3) Tilt the top view such that the vertical plane containing the generator and axis is at 45° to VP. Base nearer to VP than vertex means base faces upwards towards XY line.

Projections of Regular Pyramids Resting on a Base Corner with Slant Edge Inclined

High Priority10x in Past Papers
Rate:
Exam Sessions:
2024 Model Paper Q4June 2024Dec 2023
Question Type:15 Marks Drawing Problem
💡EXAM NOTE
Three-stage projection of triangular/square/hexagonal pyramid: (1) In simple position on HP, keep base corner on the extreme right so the slant edge appears as a true line in front view. (2) Tilt front view so that slant edge containing that base corner makes 30° with HP. Project top view. (3) Reproduce top view such that top view of axis makes 45° with XY line. Follow visibility rule: outline is always visible; edges pointing towards observer in front view are visible in top view.

Projections of Pyramids Resting on a Triangular Slant Face on HP

High Priority9x in Past Papers
Rate:
Exam Sessions:
KTU Dec 2023KTU May 2023
Question Type:15 Marks Drawing Problem
💡EXAM NOTE
When a pyramid rests on one of its triangular slant faces on HP: In stage 2, tilt the front view so that the extreme slant face (e.g. o'c'd') lies completely on the XY line. In stage 3, rotate the top view so that the axis or base edge makes the specified angle with VP. Check that all outer boundary lines in the third stage are drawn solid (visible).

Projections of Pentagonal and Hexagonal Prisms Inclined to Both Planes

High Priority8x in Past Papers
Rate:
Exam Sessions:
KTU June 2023KTU Dec 2022
Question Type:15 Marks Drawing Problem
💡EXAM NOTE
Prism resting on base edge or corner: Number top base points 1, 2, 3... and bottom base points a, b, c... Clearly distinguish between visible solid lines and hidden dashed lines in stages 2 and 3. When axis makes angle theta with HP, base makes angle (90 - theta) with HP.

Module 3Sections of Solids and Development of Surfaces (Drawing Problems)

15 Marks
Exam Focus: 100% Geometric Drawing. Sections of solids by section planes perpendicular to one plane and inclined to the other, sectional views, true shape of sections, and development of lateral surfaces of truncated solids (Radial Line & Parallel Line methods). Zero theory questions.

Section of Pyramids by Section Plane Inclined to VP / HP & True Shape of Section

High Priority10x in Past Papers
Rate:
Exam Sessions:
2024 Model Paper Q5June 2024Dec 2023Dec 2022
Question Type:15 Marks Drawing Problem
💡EXAM NOTE
When section plane is inclined to VP at 45° and perpendicular to HP: (1) The cutting plane appears as a straight line inclined at 45° in the top view at distance 10 mm from axis. (2) Project intersection points on each edge up to front view. (3) To obtain true shape of section, draw auxiliary reference line X1Y1 parallel to the section plane line in top view and project perpendicular distances from front view. Hatch section with 2H pencil lines spaced 2 mm at 45°.

Development of Lateral Surfaces of Truncated Prisms & Cylinders (Parallel Line Method)

High Priority10x in Past Papers
Rate:
Exam Sessions:
2024 Model Paper Q6June 2024Dec 2023
Question Type:15 Marks Drawing Problem
💡EXAM NOTE
Parallel line development: Total stretch-out length = perimeter of base (e.g. 5 * 25 = 125 mm for pentagonal prism; pi * D for cylinder). Mark cutting points on each vertical edge in front view and project horizontally across to corresponding development fold lines. For prisms, connect cut points with straight lines; for cylinders, connect with a smooth French curve.

Development of Surfaces of Truncated Pyramids and Cones (Radial Line Method)

High Priority9x in Past Papers
Rate:
Exam Sessions:
KTU Dec 2023KTU May 2023
Question Type:15 Marks Drawing Problem
💡EXAM NOTE
Radial Line development: Arc radius R MUST equal the TRUE slant length of the extreme edge. Subtended angle for cone sector theta=(r/R)∗360°theta = (r / R) * 360°. For pyramids, transfer all cut points from front view to the true slant edge generator before swinging arcs to the development.

Section of Cone / Cylinder by Auxiliary Planes (True Conic Sections: Ellipse & Parabola)

Medium Priority8x in Past Papers
Rate:
Exam Sessions:
KTU June 2023KTU Dec 2022
Question Type:15 Marks Drawing Problem
💡EXAM NOTE
When cutting plane cuts all generators of a cone, true shape is an ellipse. Locate major axis (length on cutting plane line in front view) and minor axis (width at midpoint projected from top view). Construct smooth true shape curve using French curve.

Module 4Isometric Projections of Combined Solids (Drawing Problems)

15 Marks
Exam Focus: 100% Geometric Drawing. Isometric projections and isometric views of combinations of two or more solids (pyramids on cylinders, cones on square slabs, spheres on frustums). Isometric scale construction. Zero theory questions.

Isometric View of a Pyramid Centrally Resting on a Cylinder

High Priority10x in Past Papers
Rate:
Exam Sessions:
2024 Model Paper Q7June 2024Dec 2023Dec 2022
Question Type:15 Marks Drawing Problem
💡EXAM NOTE
Isometric View uses TRUE lengths (100% scale) at 30° to horizontal. Steps: (1) Enclose cylinder base in a 60x60 rhombus at 30°. Draw top and bottom base ellipses using the 4-center method. (2) Height = 40 mm vertical. (3) Draw 20 mm pentagon in a box; transfer box coordinates centrally to the top face of the cylinder. (4) Raise apex 50 mm vertically from center. Connect apex to pentagon base corners. Darken visible outlines.

Isometric Projection of a Cone Surmounted over a Square / Rectangular Slab

High Priority10x in Past Papers
Rate:
Exam Sessions:
2024 Model Paper Q8June 2024Dec 2023
Question Type:15 Marks Drawing Problem
💡EXAM NOTE
Isometric PROJECTION requires drawing the ISOMETRIC SCALE first: Construct two lines at 30° (isometric scale) and 45° (true scale) from horizontal. Reduction ratio=sqrt(2/3)≈ratio = sqrt(2/3) \approx 0.816. All dimensions (60 mm slab, 20 mm thickness, 50 mm cone base, 60 mm cone height) MUST be reduced using the isometric scale before drawing. Draw cone base ellipse using 4-center method on the top face of the slab.

Isometric Projection of a Sphere Resting on a Truncated Frustum of Cone / Pyramid

High Priority9x in Past Papers
Rate:
Exam Sessions:
KTU Dec 2023KTU May 2023
Question Type:15 Marks Drawing Problem
💡EXAM NOTE
Special Rule for Sphere in Isometric Projection: The center of the sphere is located at an isometric height (RisoR_{iso}) above the top face of the frustum. BUT the sphere ITSELF always projects as a TRUE circle of TRUE radius RtrueR_{true} (not reduced) from that center point!

Isometric View of Objects with Circular / Rectangular Cutouts & Stepped Blocks

Medium Priority8x in Past Papers
Rate:
Exam Sessions:
KTU June 2023KTU Dec 2022
Question Type:15 Marks Drawing Problem
💡EXAM NOTE
Enclose the complete orthographic machine component in an overall isometric box (L x W x H). Carve out steps and cutouts from outer faces inwards. Draw circular holes on isometric planes using 4-center rhombus method on the respective isometric face.
Spot an error, wrong question, or missing topic? Let us know so we can fix it right away!
2024 SchemeBETA•60 Marks ESE•2 Hours 30 Minutes
Practice Paper Blueprint
Reg No.: _____________________Name: _____________________

KTUNOTES.LIVE PAPER (BETA)

2024 SCHEME SAMPLE QUESTION PAPER

Independent 2024 Scheme practice paper prepared by KTUNOTES.LIVE for academic revision and self-assessment. Not affiliated with or endorsed by APJ Abdul Kalam Technological University.
Course Code: GMEST103  •  Course Name: Engineering Graphics and Computer Aided Drawing
Max. Marks: 60Duration: 2 Hours 30 MinutesScheme: 2024 Scheme (4 Modules)
Instructions: Retain Construction lines. Show necessary dimensions. Answer any ONE question from each module. Each question carries 15 marks. Questions only - solve independently on drawing sheets.
PART B - DRAWING QUESTIONS
(Answer one full question from each module, each carries 15 marks)  •  4 × 15 = 60 Marks
MODULE 1
Q1.
One end of a line CD is 15 mm above HP and 20 mm in front of VP. At the same time the other end is 60 mm above HP and 50 mm in front of the VP. The distance between the end projectors is 70 mm. Draw the projections of the line and locate the traces. Determine the true and apparent lengths. Also find the true and apparent inclinations.
Module 1 • CO1 • K3
(15)
OR
Q2.
A line CD of length 65 mm is inclined at 45° to HP and 30° to VP. The end D is 50 mm above HP and 45 mm in front of VP. Draw the projections of the line and locate its traces.
Module 1 • CO1 • K3
(15)
MODULE 2
Q3.
A cone of base 40 mm diameter and axis 70 mm long has one of its generators on the HP. A plane containing that generator and the axis is perpendicular to HP and inclined at 45° to the VP. Draw the projection when the base is nearer to the VP than the vertex.
Module 2 • CO2 • K3
(15)
OR
Q4.
Draw the projections of a triangular pyramid 35 mm side and height 65 mm long, if it is resting on one of the corners of the base in HP with the slant edge containing that base corner making an angle of 30° with HP and top view of the axis making an angle of 45° with XY-line.
Module 2 • CO2 • K3
(15)
MODULE 3
Q5.
A hexagonal pyramid side of the base 30 mm and axis 70 mm rests with its base on the HP and an edge of the base inclined at 30° to VP. A section plane inclined at 45° to VP and perpendicular to HP passes through the pyramid at a distance of 10 mm from the axis and in front of it. Draw its top view, sectional front view and true shape of section.
Module 3 • CO3 • K3
(15)
OR
Q6.
A pentagonal prism side of base 25 mm and altitude 50 mm, rests on its base on the HP such that an edge of the base is parallel to VP and nearer to the observer. It is cut by a plane inclined at 45° to HP, perpendicular to VP and passing through the centre of the axis. Draw the development of the surface of the truncated prism.
Module 3 • CO3 • K3
(15)
MODULE 4
Q7.
Draw the isometric view of a pentagonal pyramid, side of base 20 mm and height 50 mm which rests centrally with base on a cylinder of diameter 60 mm and height 40 mm.
Module 4 • CO4 • K3
(15)
OR
Q8.
A cone of diameter 50 mm base and height 60 mm is surmounted over a square slab of 60 mm side and 20 mm thickness on HP so that one of the edges of the square slab is parallel to VP. Draw the isometric projection of the combination.
Module 4 • CO4 • K3
(15)
*** END OF QUESTION PAPER ***
Downloaded from https://ktunotes.liveGMEST103 • KTUNOTES.LIVE Paper (Beta)
Notice an error, typo, or formula discrepancy in this paper?